Your question: How do I reset my Gigabyte motherboard BIOS?

How do I reset my Gigabyte motherboard BIOS to default?

Method 2: Resetting the BIOS

  1. Shut off the power supply and wait 10 seconds.
  2. Press PC Power on button and PC Reset button all at the same time for about 10 seconds.
  3. Release the buttons thereafter and turn on the power supply on to start the PC as normal.

How do I reset my motherboard BIOS?

Reset the BIOS to Default Settings (BIOS)

  1. Access the BIOS Setup utility. See Accessing BIOS.
  2. Press the F9 key to automatically load the factory default settings. …
  3. Confirm the changes by highlighting OK, then press Enter. …
  4. To save the changes and exit the BIOS Setup utility, press the F10 key.

Where is the reset button on Gigabyte motherboard?

Open the computer case and locate the 3-pin jumper on the motherboard near the power supply, typically labeled “clear cmos” or “reset bios.” Remove the jumper from the default position, which is typically connecting the 1st and 2nd pins. Wait one minute. Replace the jumper to connect the 2nd and 3rd pins.

THIS IS IMPORTANT:  Quick Answer: What is export in Unix?

How do I clear the CMOS on my Gigabyte motherboard?

If there is no CLR_CMOS jumpers or [CMOS_SW] button on the motherboard, please follow the steps to clear CMOS:

  1. Take out the battery gently and put it aside for about 10 minutes or longer. …
  2. Re-insert the battery to the battery holder.
  3. Connect power cord to MB again and turn on power.

How do I troubleshoot my Gigabyte motherboard?

Make sure the motherboard does not short-circuit with the chassis or other metal objects. Check if the CPU cooler is attached to the CPU securely. Is the power connector of the CPU cooler connected to the CPU_FAN header properly? Check if the memory is installed properly on the memory slot.

Is it safe to reset BIOS to default?

It is safe to reset the BIOS to default. Most often, resetting the BIOS will reset the BIOS to the last saved configuration, or resets your BIOS to the BIOS version that shipped with the PC. Sometimes the latter can cause issues if settings were changed to take account for changes in hardware or OS after install.

How do I force my computer into BIOS?

In order to access BIOS on a Windows PC, you must press your BIOS key set by your manufacturer which could be F10, F2, F12, F1, or DEL. If your PC goes through its power on self-test startup too quickly, you can also enter BIOS through Windows 10’s advanced start menu recovery settings.

How do I reset my BIOS without a monitor?

Use the power switch at the back of the computer to disconnect the motherboard temporarily. Turn on the computer for 2 seconds and shut it off again . Repeat this 4 times and then turn on your computer normally. Your BIOS will be at default settings.

THIS IS IMPORTANT:  Can you put 2 operating systems one computer?

What is the reset button on PC?

Personal computers



The reset button would typically kick off a soft boot, instructing the computer to go through the process of shutting down, which would clear memory and reset devices to their initialized state. Contrary to the ‘Power Button’, which would simply remove power immediately.

Do you clear CMOS while PC is on?

The CMOS battery provides power used to save the BIOS settings – this is how your computer knows how much time has passed even when it’s been powered-off for a while – so removing the battery will remove the source of power and clear the settings. … There’s no reason to clear your CMOS if everything is working properly.

How do I clear CMOS with a screwdriver?

To clear the values of the CMOS, place a jumper cap on the two pins to shorten the two pins temporarily, or use a metal object like a screwdriver to touch the two pins for a few seconds. Always turn off your computer and unplug the power cord out of the power outlet before clearing the CMOS values.

What to do after clearing CMOS?

Try disconnecting the hard drive, and power on the system. If it stalls at a BIOS message saying, ‘boot failure, insert system disk and press enter,’ then your RAM is likely fine, as it’s successfully POSTed. If that’s the case, concentrate on the hard drive. Try doing a windows repair with your OS disc.

Operating system reviews